Machinery International Corporation 20 Commerce Drive
North Branford, CT 06471 USA
Tel: +1 203-484-0400
Fax: +1 203-484-4499
sales@machyintl.com
Spanish Flag French Flag German Flag Chinese Flag

16" (400mm) x .006"- .0315" (0.15-0.8mm), SUNDWIG, TENSION LEVELING LINE (12970)   Our stock number: 12970

16 (400mm) x .006 - .0315 (0.15-0.8mm), SUNDWIG, TENSION LEVELING LINE (12970)

Click on picture below for larger version
16 (400mm) x .006 - .0315 (0.15-0.8mm), SUNDWIG, TENSION LEVELING LINE (12970)16 (400mm) x .006 - .0315 (0.15-0.8mm), SUNDWIG, TENSION LEVELING LINE (12970)16 (400mm) x .006 - .0315 (0.15-0.8mm), SUNDWIG, TENSION LEVELING LINE (12970)


MACHINE# 12970

SPECIFICATIONS:

 1. MANUFACTURER : SUNDWIG GMBH (GERMANY)
 1-1. RAW MATERIAL : COLD ROLLED STAINLESS STEEL COPPER & ALLOYS
 1-2. WIDTH : 200mm ~ 400mm (7.8" - 15.7")
 NOTE: MACHINE HAS LEVELED UP TO 450MM (18") WIDE MATERIAL
 1-3. THICKNESS : 0.15mm ~ 0.8mm (0.006" - 0.0315") STAINLESS
 1-4. MECHANICAL PROPERTIES
YIELD STRENGTH : 100 KG (220 LBS.) MAXIMUM
 1-5. INCOMING/RECOILING COIL SPEC.
COIL I.D : 508mm (20")
COIL O.D : 1,800mm (70") MAXIMUM
COIL WEIGHT : 8,000 KG (17,636 LBS.) MAXIMUM
(INCLUDING SLEEVE & INTERLEAVE PAPER)
 1-6. LINE SPEED : MAXIMUM 60 MPM (200 FPM)
THREADING / : 15 MPM (50 FPM)
 1-7. TENSION
UNCOILER : 500 KG (1,100 LBS.) MAXIMUM
TENSION LEVELLER : 11,000 KG (24,250 LBS.) MAXIMUM
RECOILER : 500 KG (1,100 LBS.) MAXIMUM
 1-9. HYDRAULIC SOURCE :
 MAXIMUM PRESSURE: 140 Kg (308 LBS.)
 NORMAL PRESSURE: 100 Kg (220 LBS.)
1-10. ELECTRICAL SOURCE :
 MAIN POWER VOLTAGE : AC 440 V, 60 HZ, 3 PHASE
 CONTROL VOLTAGE : AC 220 V, 60 HZ, SINGLE PHASE
1-11. COMPRESSED AIR SOURCE :
 MAXIMUM PRESSURE: 7 kg (15.5 LBS.)
 NORMAL PRESSURE: 5 kg (11 LBS.)
ALL THE SPECIFICATION SHOULD BE CHECKED AND CONFIRMED BY BUYER

LINE CONSISTS OF:

3. TECHNICAL SPECIFICATION
3-1. PAPER WINDER
- TYPE : SINGLE WINDING -AIR SHAFT TYPE
- INNER DIAMETER OF SPOOL : 125mm (5")
- TENSION CONTROL : TORQUE MOTOR
- MAX. OD :  500mm (20")
THE PAPER WINDER DRIVEN BY TORQUE MOTOR, WILL REWIND INTERLEAF PAPER FROM
THE COIL.

3-2. ENTRY COIL CAR
- TYPE : POWERED LIFT HYDRAULIC CYLINDER MOVING TYPE
- LIFTING METHOD : BY HYDRAULIC CYLINDER
- LIFTING STROKE : 400mm (15 3/4") MAXIMUM
- LIFTING CAPACITY : MAX. 4,000 KG (8,818 LBS.)
THE COIL CAR WILL INSTALLED TO LIFT THE COIL TO MATCH THE CENTER LINE TO
THE MANDREL OF THE PAY OFF REEL. THE MOVING OF THE CAR WILL BE PUSHED
OR PULLED BY THE HYDRAULIC CYLINDER

3-3. DEFLECTOR ROLL
- TYPE : NIP ROLL TYPE
- ROLL SIZE :  400mm (15 3/4") x 500mm (20") LONG (SAME W/THE BRIDLE ROLL)
- DRIVE : IDLE ROLL
THE DEFLECTOR ROLL WILL BE INSTALLED BETWEEN EXIT BRIDLE AND THE
TENSION REEL FOR THE SMOOTH WINDING AT THE TENSION REEL MANDREL.

3-4. EPC SYSTEM
-LOCATION : IN FRONT OF THE DEFLECTOR ROLL
-ADJUSTING RANGE : +/- 75mm (2.95")
EPC SYSTEM WILL BE SUPPLIED BY THE EMG GERMANY AND THE RELATED
MODIFICATION SUCH AS THE SLIDING BED MANUFACTURING, SENSOR MOVING HEAD
MANUFACTURING AND HYDRAULIC POWER SUPPLY WILL BE DONE BY LOCALLY.
3-5. PAPER UNWINDER
- TYPE : SINGLE WINDING -AIR SHAFT TYPE
- INNER DIAMETER OF SPOOL : 125mm (5")
- TENSION CONTROL : BRAKE CONTROL
- MAX. OD :  500mm (20")
THE PAPER UNWINDER WILL BE BRAKED BY BAND BRAKE FOR MAINTAIN TENSION
DURING UNWINDING, WILL UNWIND INTERLEAF PAPER FROM THE COIL.
3-6. EXIT COIL CAR
- TYPE : POWERED LIFT HYDRAULIC CYLINDER MOVING TYPE
- LIFTING METHOD : BY HYDRAULIC CYLINDER
- LIFTING STROKE : 400mm (15 3/4") MAXIMUM
- LIFTING CAPACITY : MAX. 4,000 KG (8,818 LBS.)
THE COIL CAR WILL INSTALLED TO LIFT THE COIL TO MATCH THE CENTER LINE TO
THE MANDREL OF THE TENSION REEL. THE MOVING OF THE CAR WILL BE PUSHED
OR PULLED BY THE OPERATOR
5 - 5
3-5. HYDRAULIC SYSTEM
- PUMP & MOTOR : 3 SET
2 PUMPS IN OPERATION & 1 UNIT STAND-BY
- KIND OF FLUID : MINERAL OIL
- ACCESSORY : OIL COOLER, OIL HEATER, DOUBLE FILTER
THERMO DETECTOR AND THERMO METER
LEVEL DETECTOR AND LEVEL GAUGE
PUMP UNLOADING CIRCUIT
MAGNETIC SEPARATOR ETC.
3-6. ELECTRIC SYSTEM
- MAIN POWER SOURCE : AC 440V, 60HZ, 3 PHASE
- CONTROL SOURCE : AC 220V, 60HZ, SINGLE PHASE AND DC 24V
- DC MOTOR : USED EQUIPMENT
- DC DRIVE : NEW CONTROLS
HARDWARE MADE BY EUROTHERM
- AC MOTOR CONTROL : AC MOTOR & AC MOTOR CONTROL
- PLC SYSTEM : PLC HARDWARE AND SOFTWARE
HARDWARE MITSUBISHI OR EQUIVALENT
- MAIN OP DESK & LOCAL OP STAND
MAIN OP DESK : PENDANT TYPE
LOCAL OP PANEL : WALL MOUNTED TYPE / POLE MOUNTED TYPE
3-7. OPERATING SPARE PARTS
- WORK ROLL FOR TENSION LEVELER 2 SET
- INTERMEDIATE ROLL FOR LEVELER 1 SET

PHOTOS AND LAYOUT DRAWING ARE AVAILABLE BY REQUEST.

     **PRICE QUOTED AS IS WHERE IS SUBJECT TO PRIOR SALE**

**ALL SPECIFICATIONS ARE SUBJECT TO VERIFICATION BY PURCHASER**



Get a Quote

Company:
Contact:
Email:
Tel:
Address:
City St ZIP:
Fax:

How did you hear of us?
Additional information on your request:
   

Please enter text from above:

 |  Machinery International Corporation  |  Contact Us  |  Email Sales Department  |  203.484.0400  | 

RETURN to complete inventory display       RETURN to our home page